流固耦合分析實例
2016-09-20 by:CAE仿真在線 來源:互聯網
ANSYS+ FLUENT流-熱-固多場耦合工程實踐核心技術培訓
length=2 !定義體各種變量參數,長寬高
width=3
height=2
/prep7
et,1,63 !選用殼模型
et,2,30 !選用FLUID30單元,用于流固耦合問題
r,1,0.01 增加實常數,殼厚為0.01
mp,ex,1,2e11
mp,nuxy,1,0.3
mp,dens,1,7800 !定義殼單元的各種單元屬性
mp,dens,2,1000 !定義Acoustics材料來描述流體材料-水
mp,sonc,2,1400 !定義聲單元聲速
mp,mu,0, !定義吸聲系數
!
block,,length,,width,,height !建立長方體
esize,0.5
mshkey,1
!
type,1 !選擇殼單元
mat,1
real,1
asel,u,loc,y,width !選擇面
amesh,all!劃分面單元
alls !選擇所有項
!
type,2 !選擇聲單元
mat,2
vmesh,all!劃分體單元
fini
/solu
antype,2
modopt,unsym,10 !非對稱模態提取方法處理流固耦合問題
eqslv,front
mxpand,10,,,1
nsel,s,loc,x,
nsel,a,loc,x,length
nsel,r,loc,y
d,all,,,,,,ux,uy,uz,
nsel,s,loc,y,width,
d,all,pres,0 !上面幾步為定義邊界條件和約束
alls
asel,u,loc,y,width,
sfa,all,,fsi !定義流固耦合界面
alls !選擇所有項
solv !求解
fini
/post1 !后處理
set,first
plnsol,u,sum,2,1 !顯示圖形
fini
/PREP7
!定義殼材料與性質
!殼元素與材料
ET,1,shell63 $MP,EX,1,201E9 $MP,prxy,1,0.26 $MP,dens,1,7.85E3 $r,1,0.006
!流體元素與材料
ET,2,FLUID80 $MP,EX,2,1.5e9 $MP,DENS,2,0.84e3 $mp,visc,2,1.0e-10
!以下這個keyoption怎么用? 如過用1,就會顯示[Element 877 may not have a positive Z coordinate IF KEYOPT(2) = 1.],顯示這個錯誤代表要做什么修正嗎?所以我暫時用KEYOPT(2) = 0就可以跑。
KEYOPT,2,2,0
!建立殼關鍵點
K,1,10,0,0 $K,2,10,0,12
!建立中心線關鍵點
k,3,0,0,0 $k,4,0,0,20
!定義殼壁線
L,1,2 $L,1,3
!以關鍵點3,4為中心線旋轉360度生成殼體
AROTAT,all,,,,,,3,4,360
!劃分殼體網格
AATT,1,1,1 $esize,2 $mshape,0,3D $mshkey,2 $amesh,all $alls
!延伸出水位體積
VEXT,2,8,2,0,0,10,0,0,0 $vglue,all
csys,1
!劃分水位網格
type,2 $mat,2 $esize,2 $mshape,0,3D $mshkey,1 $vmesh,all
alls
!以上建模應該沒太大問題
!以下是耦合,我在流固界面上的網格是重合節點,特別是下面這兩段落我很不確定該怎么設定,感覺問題就出在這邊了!這里解決了應該就可以。要怎么改?或是用CP? 或是NUMMRG? 重點是流體和固體要一起動,通常設定不好就流體自己動,或是流體都跑到殼體外面去了,流體跟殼不應該穿越,而是一起有行為。
csys,1 !將工作平面定義為柱坐標。
nsel,s,loc,x,10
nrotate,all !旋轉節點坐標系。
CPINTF,UX,0.0001, !將徑向約束(即X方向)加到節點上。
nsel,s,loc,z,0
nrotate,all
CPINTF,UZ,0.0001,
!邊界條件,將底部固定,并給予Z方向加速度。
NSEL,S,LOC,Z,0 $D,ALL,ALL $acel,,,9.8
fini
/solu
antype,modal
modopt,reduc,10,,
mxpand,10,
csys,1!Z上柱坐標系
!定義主自由度,由圖顯示感覺是沒問題,但我也不太確定。
Esel,s,type,,1 !選擇殼
Nsle,s,all !所有點
Nsel,u,loc,z,0 !排除邊界條件
m,all,ux !(徑向)x方向的主自由度
Esel,s,type,,2 !選擇液體
Nsel,s,loc,z,10 !再選擇液面表面
m,all,uz !(豎向)z方向的主自由度
alls
solve
fini
水壩空庫
/BATCH
KEYW,PR_SET,1
KEYW,PR_STRUC,1
KEYW,PR_THERM,0
KEYW,PR_FLUID,0
KEYW,PR_ELMAG,0
KEYW,MAGNOD,0
KEYW,MAGEDG,0
KEYW,MAGHFE,0
KEYW,MAGELC,0
KEYW,PR_MULTI,0
KEYW,PR_CFD,0
/GO
!*
/prep7
!* define material proterties
mp,dens,1,2650. !mat 1 for dam
mp,ex,1,3.15e10
mp,prxy,1,.167
!* define element type
et,1,PLANE42,,,2
!* define geometry
lwater=618.
k, 1,0.0,0.0,0.0
k, 2,70.2,0.,0.
k, 3,0.,66.5,0.
k, 4,21.9875,66.5,0.
k, 5,0.,103.,0.
k, 6,14.8,103.,0.
a, 1, 2, 4, 3
a, 3, 4, 6, 5
asel,s,loc,x,0.,100.
aatt,1,,1
cm,adam,area
allsel,all
!* mesh geometry
ESIZE,0,10
lsel,s,loc,y,0.1,66. !壩下部剖分分?jǐn)?shù)
lesize,all,,,15
mshape,0,2D
mshkey,1
allsel,all
amesh,all
finish
/solu
antype,modal
MODOPT,LANB,30
MXPAND,30, , ,0
esel,s,mat,,1 !壩體約束
nsle,s
nsel,r,loc,y,-1.0,1.0
d,all,ux,0.
d,all,uy,0.
/pbc,all,,1
/pnum,type,1
/number,1
gplot
allsel,all
save
solve
滿庫
/BATCH
KEYW,PR_SET,1
KEYW,PR_STRUC,1
KEYW,PR_THERM,0
KEYW,PR_FLUID,0
KEYW,PR_ELMAG,0
KEYW,MAGNOD,0
KEYW,MAGEDG,0
KEYW,MAGHFE,0
KEYW,MAGELC,0
KEYW,PR_MULTI,0
KEYW,PR_CFD,0
/GO
!*
/prep7
!* define material proterties
mp,dens,1,2650. !mat 1 for dam
mp,ex,1,3.15e10
mp,prxy,1,.167
mp,dens,2,1000. !mat 2 for water
mp,sonc,2,1440
!* define element type
et,1,PLANE42,,,2
et,2,29
et,3,29,,1
!* define geometry
lwater=618.
k, 1,0.0,0.0,0.0
k, 2,70.2,0.,0.
k, 3,0.,66.5,0.
k, 4,21.9875,66.5,0.
k, 5,0.,103.,0.
k, 6,14.8,103.,0.
k, 7,-1.*lwater,103.,0.
k, 8,-1.*lwater,66.5,0.
k, 9,-1.*lwater,0.,0.
a, 1, 2, 4, 3
a, 3, 4, 6, 5
a, 8, 3, 5, 7
a, 9,1, 3, 8
asel,s,loc,x,0.,100.
aatt,1,,1
cm,adam,area
asel,s,loc,x,-1*lwater,0.
aatt,2,,3
cm,awater,area
allsel,all
!* mesh geometry
ESIZE,0,10
lsel,s,loc,y,0.1,66. !壩下部剖分分?jǐn)?shù)
lesize,all,,,15
lsel,s,loc,x,-0.1,-1*lwater-1. !水體長度方向剖分分?jǐn)?shù)
lsel,r,loc,y,-0.1,67.
lesize,all,,,40,0.5
lsel,s,loc,x,-0.1,-1*lwater-1. !水體長度方向剖分分?jǐn)?shù)
lsel,r,loc,y,100.,104.
lesize,all,,,40,2.0
mshape,0,2D
mshkey,1
allsel,all
amesh,all
!更改與水體接觸的單元類型
esel,s,type,,3
nsle,s
nsel,r,loc,x,-1.,1.
esln,r
emodif,all,type,2
allsel,all
finish
/solu
antype,modal
MODOPT,UNSYM,30
MXPAND,30, , ,0
/pnum,type,1
/number,1
nsel,s,loc,x,-1.,1. !庫水壩體FSI面
esln,s
esel,r,mat,,2
sf,all,fsi
esel,s,mat,,1 !壩體約束
nsle,s
nsel,r,loc,y,-1.0,1.0
d,all,ux,0.
d,all,uy,0.
esel,s,mat,,2 !水體表面約束
nsle,s
nsel,r,loc,y,102.,104.
d,all,pres,0.
/pbc,all,,1
/psf,fsi,,2
allsel,all
gplot
save
solve
相關標簽搜索:流固耦合分析實例 Fluent培訓 Fluent流體培訓 Fluent軟件培訓 fluent技術教程 fluent在線視頻教程 fluent資料下載 fluent分析理論 fluent化學反應 fluent軟件下載 UDF編程代做 Fluent、CFX流體分析 HFSS電磁分析